Docs2.fortinet.com

Health check options FortiGate / FortiOS 7.0.0 Fortinet …

WebHealth check options. Health checks include several protocols and protocol specific options. The health check protocol options include: Use PING to test the link with the server. Use …

Actived: Just Now

URL: https://docs2.fortinet.com/document/fortigate/7.0.0/administration-guide/920631/health-check-options

Passive WAN health measurement FortiGate / FortiOS …

WebPassive WAN health measurement. SD-WAN passive WAN health measurement determines the health check measurements using session information that is captured …

Category:  Health Go Health

Using SNMP to monitor health check FortiGate / FortiOS …

WebExample. This example shows a SD-WAN health check configuration and its collected statistics. To configure the SD-WAN health check: config system sdwan set status …

Category:  Health Go Health

SD-WAN health check packet enhancement New Features

WebSD-WAN health check probe packets now support Differentiated Services Code Point (DSCP) markers for accurate evaluation of the link performance for high priority …

Category:  Health Go Health

Check HA synchronization status FortiGate / FortiOS …

WebCheck HA synchronization status. The HA synchronization status can be viewed in the GUI through either a widget on the Dashboard or on the System > HA page. It can also be …

Category:  Health Go Health

ADOM health check tool reports warnings on devices

WebFrom the System Settings > All ADOMs pane, you can check the status of all devices in all ADOMs. You can check the status of the following criteria for all devices in all ADOMs: …

Category:  Health Go Health

Monitoring health check status FortiADC 7.4.1 Fortinet …

WebMonitoring health check status. FortiADC enables you to monitor the health of servers in real time directly from your desktop, as described below.. Before you begin: You must …

Category:  Health Go Health

Link health monitor FortiGate / FortiOS 6.4.5 Fortinet …

WebTo configure a link health monitor in the GUI: Go to Network > Performance SLA and click Create New. Set a Name for the SLA. Set the Protocol that you need to use for status …

Category:  Health Go Health

Monitor performance SLA FortiGate / FortiOS 7.0.2

WebYou can monitor the link quality status of SD-WAN interface members by going to Network > SD-WAN and selecting the Performance SLAs tab. The live charts show the packet loss, …

Category:  Health Go Health

Configuring SD-WAN in an HA cluster using internal …

WebOn the primary FortiGate, go to Network > SD-WAN.. Set Status to Enable.. In the SD-WAN Interface Members section, click Create New.The New SD-WAN Member …

Category:  Health Go Health

Configuring HA settings specifically for active-passive and …

WebHA Static Route and Policy Route. Unlike the Static Route and Policy Route in System > Network > Route which are synchronized to all the HA members, the configurations in …

Category:  Health Go Health

Firmware upgrade basics FortiGate / FortiOS 7.4.0 Fortinet …

WebTo make sure a FortiGate-7000E firmware upgrade is successful, before starting the upgrade Fortinet recommends you use health checking to make sure the FIMs and …

Category:  Health Go Health

Firmware upgrade basics FortiGate / FortiOS 7.2.8 Fortinet …

WebVerify the recommended upgrade path as documented in the release notes. Back up your FortiGate 7000F configuration. To make sure a FortiGate 7000F firmware upgrade is …

Category:  Health Go Health

Check HA sync status FortiGate / FortiOS 6.4.2 Fortinet …

WebCheck HA sync status. The HA sync status can be viewed in the GUI through either a widget on the Dashboard or on the System > HA page. It can also be confirmed through the …

Category:  Health Go Health

HA cluster firmware upgrades FortiGate / FortiOS 7.2.5 Fortinet

WebTo make sure a FortiGate-6000 firmware upgrade is successful, before starting the upgrade Fortinet recommends you use health checking to make sure the management board and …

Category:  Health Go Health

Embedded SD-WAN SLA information in ICMP probes 7.2.1

Webdetect-mode {active | passive | prefer-passive | remote} Set the mode that determines how to detect the server: active: the probes are sent actively (default).; passive: the traffic …

Category:  Health Go Health

Configuring FortiManager FortiGate / FortiOS 7.2.2 Fortinet

WebTo add a FortiManager to the Security Fabric using the GUI: On the root FortiGate, go to Security Fabric > Fabric Connectors and double-click the FortiManager card. The …

Category:  Health Go Health

SLA monitoring using the REST API FortiGate / FortiOS 6.2.2

WebThe Fortinet Cookbook contains examples of how to integrate Fortinet products into your network and use features such as security profiles, wireless networking, and VPN. Using …

Category:  Health Go Health

Monitoring performance SLA FortiGate / FortiOS 7.4.0 Fortinet

WebYou can monitor the link quality status of SD-WAN interface members by going to Network > SD-WAN and selecting the Performance SLAs tab. The live charts show the packet loss, …

Category:  Health Go Health